|
-
Frame:
Complete jig-welded original style 4” round tube frame.
Includes all mounts ready to accept small block Ford and
1987-2004 Mustang running gear. Kit can be ordered to
accept a wide variety of engines/suspensions.
-
Comes
powdercoated in gloss black
-
Includes three
point roll bar powdercoated to match
-
Includes mounts
to accept passenger side roll bar.
-
Body:
Hand laid 3/16” laminate composite body and panels made with
vinylester resin.
-
Driver and
Passenger doors with new molded door liners
-
Hood with new
molded hood liner, and centered hood scoop
-
Trunk with new
molded trunk liner and improved mount face for lic plate
light.
-
Includes
secondary body fasteners assembly.
-
Adhesive
backed and foam weatherstrip
-
C-channel
door edge trim and fasteners
-
Plastic end
caps and body u-nut fasteners
-
Trunk and
engine bay seal, push on rubber bulb seal
-
Rubber hood
and trunk bumpers
-
Includes
multi-adjustable door hinges with bronze bushings
w/fasteners
-
Includes vintage
trunk hinge kit, hinge support plates and fasteners
-
Includes hood
hinge kit with hydraulic piston supports and fasteners
Includes original design quick-jack competition bumpers
w/stainless steel sleeves and fasteners.
-
Chassis Aluminum
Panels: Includes over 40 CNC cut, pre-formed 6061-T6
aluminum panels for cockpit, trunk, and engine bay.
-
1200 pre-packaged
rivets1/8” short & long, 3/16” short & long
-
Complete Mk3
cockpit aluminum with optional block-off plates and patch
covers
-
Engine bay
aluminum assembly with aluminum nose sections and splash
guards
-
Aluminum trunk
liner has been replaced by molded trunk liner
-
Complete Front
Suspension: Unequal length a-arm control arms with
coil-over shock suspension. Comes complete with all parts
and fasteners.
-
Koni brand high
performance mono-tube, rod-end shock absorbers
-
Coil-over kit for
Koni dampers including spring hat, threaded seat and 500lb.
black powdercoated performance springs
-
Adjustable upper
control arms with ball joints and fasteners
-
Lower tubular
control arms with ball joints and fasteners
-
Grade-8 mounting
hardware.
-
Complete Rear
Suspension: High-end 3-link deluxe rear suspension
with new Ford Racing 8.8” rear solid axle/differential with
posi-traction and 3.55 gears. Comes with all fasteners and
hardware required to install.
-
Factory New Ford
Racing 8.8” posi solid axle rear end w/3.55:1 gears in
59.25” width (87-93 size), 5-lug.
-
FFR Deluxe 3-Link
suspension kit w/rear-end brackets, upper link kit, and
fasteners, including pan-hard bar kit w/rod-ends and gr8
fasteners.
-
Koni brand high
performance mono-tube, rod-end shock absorbers
-
Coil-over kit for
Koni dampers including spring hat, threaded seat and 350lb.
black powdercoated performance springs
-
Factory Five
tubular rear lower control arms, w/polyurethane bushings and
fasteners
-
Complete
Front/Rear Brake Kit:
-
S/N 95 style spindles and spindle adapter bracket w/fasteners
-
Front hubs,
fasteners and dust covers
-
Front Brakes,
Ford GT 11” front rotors w/twin piston calipers, brake pads and
fasteners
-
Rear Brakes, Ford
10.5” rear rotors w/calipers, brake pads, slider and caliper
axle mount brackets, and fasteners.
-
Master cylinder
(listed in pedal box assembly), stainless braided brake
line, front and rear w/mount clips, banjo bolts and brake
line mounting fasteners
-
Pre-flared 3/16”
brake line and brake line T-adapter
-
OEM Ford Mustang
emergency brake handle, fasteners and cable
-
Complete Steering
System: Complete steering system using 15:1 manual
rack from tie rod ends and fasteners to vintage steering wheel
and badges. Collapsible design.
-
15:1 Manual
steering rack w/inner and outer tie rod ends and fasteners
-
Polyurethane
steering rack bushings and fasteners
-
Steering rack
shaft adapter 9/16-26 spline
-
Nickel plated
lower steering shaft (fully welded u-joints)
-
Collapsible upper steering
shaft, w/friction washers
-
14” Vintage wood
and aluminum steering wheel w/boss and ceramic F5R center
section and fasteners
-
Steering bearings
and hardware, including flange bearing, pillow block bearing
and fasteners
-
Complete Fuel
System/Parts: Based on OEM style fuel tank and
system, this assembly provides everything from the gas cap to
the lines, and is designed to work with carburetors or fuel
injection systems. External fuel pump required.
-
OEM style fuel
tank w/mounting straps and hardware, vents, gaskets, pick-up
and fuel level sending unit
-
Fuel lines,
connectors, filler neck and fasteners
-
Pre-flared fuel
lines (1/4” and 5/16”) w/unions, barbs, hose clamps and high
press flex lines and fasteners
-
Aston LeMans
style polished aluminum fuel cap with integral pressure
cap, gaskets, ground strap, fuel hose to tank w/fasteners.
-
3/8” line fuel
filter, connectors and hose clamps
-
Complete Cooling
System/Parts: Electric cooling fan and mounting hardware,
extensions for radiator hoses, and all necessary fasteners.
-
Electric cooling
fan and mounting kit w/connectors
-
Aluminum radiator
w/cap and in-line filler neck
-
Radiator mount
kit and fasteners
-
Stainless Steel
radiator hose kit incl. adapter kit, fasteners and hose
-
Overflow tank
w/cap, hoses, hose clamps and mounting hardware
-
185 degree
thermostat switch and wiring
-
Engine
Accessories/Side Exhaust/Mounts: The Mk3 Complete kit
is configured to accommodate the engine of your choice.
Select from full tubular 4-into-4-into 1 headers and side
exhaust, engine and transmission mounts.
-
Engine/Transmission mounts (select 302/351 or 4.6L, or
390/427/428, or 429/460), with fasteners
-
Exhaust, with
gaskets and fasteners. Select from
-
87-95
straight pipes
-
96-04
straight pipes
-
302 Headers,
ceramic coated
-
351 Headers,
ceramic coated
-
390/427/428
Headers, ceramic coated
-
429/460
Headers, ceramic coated
-
87-95
Catalytic converters w/air hose, check valve, T-hose
fitting
-
96-04
Catalytic converters
-
4.6L 2-Valve
Headers, ceramic coated
-
4.6L 4-Valve
Headers, ceramic coated
-
Side
Exhaust, bare steel w/rubber hanger brackets, gaskets and
fasteners
-
Driveshaft:
Select from one of three available driveshafts w/fasteners to
match the engine/trans of your choice. Select one of the
following…
-
28 spline 10.375”
driveshaft for T-5 or Tremec 3550’s
-
31 spline 10.375”
driveshaft for Tremec TKO 500 or 600’s
-
31 spline 12.875”
driveshaft for 4.6L engines w/T-45’s or 3650’s
-
Gauges and Dash
and Electrical Assembly: End those wiring harness
woes, integrated harness and electronic gauges are just the
start of this massive assembly. Choose either
vintage/replica or modern/ performance gauges to complement an
authentic 427 street style dash. Complete assembly comes with
covered aluminum dash, dash buttons, toggles and indicator
lights, switches, and horn.
-
Mk3 pre-cut 427
style aluminum dashboard w/fasteners
-
Padded dash
cover, black vinyl
-
Custom fit
chassis wiring harness
-
Ignition switch
and F5R key, headlight switch, 3-position turn signal
switch, starter solenoid and horn.
-
Dash indicators,
Red, Green, Blue dash lights
-
Wiring harness
mounting kit and hardware incl. Fuse panel mount
-
Insulated line
clip hardware and fasteners
-
Cable ties, wire
loom and flex grommeting
-
On/Off switch,
horn button, flasher and all connectors
-
Battery ground
strap
-
Battery Box and
Relocation Kit: Trunk mounted battery box, cables and
hold-downs with fasteners.
-
Speedometer
sending unit, pigtail, fasteners and 3.55 gear
-
Choose a complete
set of 7 Autometer Ultra-Light electronic gauges,
w/connectors, terminals and installation kit. Includes
the following gauges:
-
Speedometer
-
Tachometer
-
Oil Pressure
Gauge
-
Water
Temperature Gauge
-
Fuel Level
Gauge
-
Voltmeter
-
Oil
Temperature Gauge
OR Select
-
Complete set of 7
vintage F5R Replica gauges w/connectors, terminals and
installation kit includes
-
Speedometer,
reverse read
-
Tachometer
-
Oil Pressure
Gauge
-
Water
Temperature Gauge
-
Fuel Level
Gauge
-
Voltmeter
-
Clock
-
Complete Interior Accessories:
The Mk3 Complete kit
comes with all the interior accessories you need and want.
Authentic 427 seats, door latches, toggles, rear view mirror,
and more complement the dash and gauges assembly for a full
interior that is period correct. Check out this full list
of standard parts and assemblies.
-
Authentic 427
roadster metal framed seats, black vinyl w/fasteners
-
5-point Simpson
Brand harnesses. 3” wide driver and passenger, frame
mounted w/fasteners
-
Complete cockpit
carpet set, black all-weather
-
Emergency brake
boot, black vinyl
-
Authentic
interior rear view mirror w/fasteners
-
Full 7-gauge
electronic F5R Vintage gauges or Autometer Ultra-Lite gauges
(see description above in gauge assembly)
-
Original style
door latches, fasteners and leather check straps
-
Authentic
stainless
shifter handle, shift knob, boot, polished ring and
fasteners
-
Authentic 14”
wood and aluminum steering wheel (listed in steering
assembly), w/polished aluminum boss and small center badge.
-
Exterior
Accessories and Lighting: Along with the goodies on
the inside of the car, the Mk3 complete kit is loaded with the
right exterior parts and trim on the outside.
-
Wiper kit,
complete original style cable-drive Lucas wiper kit includes
motor, wheelbox, ferrules, arms, blades, dash switch, wiring
and connectors/fasteners
-
Wiper hole
drilling kit and installation kit
-
Authentic
Chrome-on-Brass vintage windscreen, tinted with side bars
and fasteners. DOT safety glass compliant
-
Authentic 427
three-lock set including T-trunk handle, L-shaped hood
handles, matching keys, cam wedges, fasteners, latch pin
sleeves and plastic end cap
-
Authentic license
plate light and bracket with fasteners
-
Authentic 3.5”
Aston roller gas cap, polished cast aluminum with adaptor
kit and all fasteners.
-
Competition hood
pins.
-
High quality
laser-cut aluminum side louvers.
-
Ceramic F5R
badging nose and tail
-
Original style
headlamp assemblies, including buckets, halogen headlamps,
trim rings, and fasteners (DOT approved).
-
Original style
British front amber turn signals, and red rear
tail-lights
-
All lighting is
DOT approved.
-
Complete Pedal Box
and Components: Leaving the Mustang pedal box behind,
the complete Mk3 kit utilizes the proven Wilwood brand pedal box
w/fasteners and all the required ancillary parts.
-
Wilwood pedal box
and mounting hardware
-
Master Cylinders,
clutch quadrant, clutch cable, threaded firewall adjuster
-
Accelerator pedal, accelerator cable, return spring and ball
stud retainer, w/fasteners
-
Brake line adapters and T-fittings
-
Oil Filter
Re-locater/Alternate Drive Pulley Assemblies: A cool
oil filter relocate kit comes with all hoses and hardware.
Other parts to help 302 EFI and Mustang engine users include…
-
Oil filter
relocate mount with fittings, hoses, barbs and fasteners
-
Spin-on engine
block adapter
-
Alternate drive
pulley, spacer, pulley wheel and fasteners
-
Air filter,
conical
-
Fan belt, six rib
-
87-95 Mk3 Roadster
Assembly Manual: Bound assembly manual that is over
200 pages long.
-
Fasteners:
Over 1500 top quality zinc plated, chrome and stainless steel
USS and SAE fasteners, numbered and packed individually by
assembly.
Click here to return to Complete Kit main page. |
